Carlton 1712 Operator's Manual Page 155
- Page / 165
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CAUTION
Do not mix Lithium, calcium, sodium or barium complex greases
due to possible compatibility problems. When changing from one
type of grease to another, it is necessary to insure all the old
grease has been removed.
If your axles are equipped with oil-lubricated hubs, then your lubrication procedure is to
periodically fill the hub with high quality hypoid gear oil to the level indicated on the clear
plastic oil cap. The oil can be filled through the rubber plug hole in the cap.
Recommended Wheel Bearing Lubrication Specifications
Grease:
Thickener Type ........................................... Lithium Complex
Dropping Point ............................................ 230°C (446°F) minimum
Consistency ................................................. NLGI No. 2
Additives ..................................................... EP, Corrosion & Oxidation Inhibitors
Base Oil ....................................................... Solvent Refined Petroleum Oil
Base Oil Viscosity ....................................... @40°C (104°F) 150cSt(695 SUS) Min.
Viscosity Index ............................................ 80 Minimum
Pour Point .................................................... -10°C (14°F) Minimum
Approved Sources:
Mobil Oil ..................................................... Mobilgrease HP
Exxon/Standard ........................................... Ronex MP
Kendall Refining Co. ................................... Kendall L-427
Ashland Oil Co. ........................................... Valvoline Val-plex EP Grease
Pennzoil Prod. Co. ....................................... Premium Wheel Bearing Grease 707L
Oil:
SAE 90 Hypoid Gear (Hypoid Rear Axle Oil)
Use only with hubs equipped with oil option.
Approved Sources:
Union Oil Co. .............................................. Union MP, Gearlube - LS
Exxon Co. USA ........................................... Gear Oil GX 80W-90
Mobil Oil Corp.. .......................................... Mobilube SHC 75W-90
Pennzoil Prod. Co. ....................................... Multipurpose Gear Lubricant 4092,
................................................................. Multipurpose Gear Lubricant 4096
- 12” Disk Style Brush Chipper 1
- CALIFORNIA 3
- Proposition 65 Warning 3
- IMPORTANT NOTICE 21
- Warranty Validation Form 23
- ® Chipper 27
- ® also reserves the right to 28
- We Pride Ourselves 29
- SAFETY FIRST ALWAYS! 31
- CUTTER DISK 33
- SAFETY: 36
- HITCH & HITCH BOLTS 38
- CUTTER DISK HOOD HINGE 39
- HOOD PIN & PADLOCK 39
- CHIPPED KNIFE 39
- ANVIL WORKING EDGE 40
- ® Starplex II 42
- BYPASS SWITCH 43
- VOLTAGE METER 43
- OIL PRESSURE 43
- ENGINE TEMPERATURE 43
- ® monitors the 44
- ® control is 44
- ® control 44
- ® manual 44
- LIFT CYLINDER 48
- LIFT CONTROL VALVE 48
- STAND ALONE OPERATION 49
- FRONT JACK STAND 49
- HYDRAULIC WINCH 52
- CONTROL VALVE 52
- SELECTOR VALVE 52
- ALWAYS WIND ROPE 53
- UNDER THE WINCH 53
- CONNECT LIGHTS 55
- INFEED TRAY LOCK PIN 56
- IN STORAGE POSITION 56
- (ONE ON EACH SIDE OF 56
- CHIPPER) 56
- SPRING LOCK PIN 56
- SPRING LOCK PIN 58
- ENGINE OPTION 60
- AUTO-FEED® ONAUTO-FEED® OFF 62
- AND BUTT END FIRST 64
- LEVER 2 68
- LEVER 1 68
- WINCH CONTROL VALVE 69
- (IF EQUIPPED) 69
- SHUT DOWN PROCEDURES 70
- BOTH SIDES OF INFEED CHUTE 71
- ROTATE CHUTE 71
- RADIATOR SCREEN 73
- CLEAN FROM THIS SIDE 73
- RADIATOR FAN 73
- ENGINE OIL FILTER 73
- MAIN FILTER SAFETY FILTER 73
- COOLANT FILLER CAP 74
- COOLANT TANK COVER 74
- ON TOP OF ENGINE 74
- FUEL FILTER 74
- FEED CONTROL LINKAGE 75
- ® Axles supplied in this 78
- Starplex II grease 79
- HYDRAULICS 85
- ® STARPLEX II 90
- CLUTCH ENGAGEMENT 94
- END OF THE CROSS-SHAFT 95
- REMOVE NAMEPLATE 95
- ADJUSTING RING NOTCH 95
- ADJUSTMENT LOCK 95
- CUTTER SYSTEM 100
- BELT TENSION 107
- ENGINE SLIDE BOLT 108
- INSIDE JAM NUT 108
- OUTSIDE JAM NUT 108
- OUTSIDE JAM 110
- INSIDE JAM 110
- LOCATION ON SHAFT 112
- BEFORE REMOVING 112
- MARK BUSHING 112
- FEED WHEEL MOTOR 114
- 6-WAY PLUG DESCRIPTION 119
- COLOR CODES 119
- Carlton 123
- IN (GND) B 143
- 2. Operating 144
- 6. Setting 148
- Auto-FeedReverse 150
- 0.5 sec 0.5 sec 0.5 sec 151
- 7. Technical features 152
- CAUTION 155
- Product Features 157
- WINCH INFORMATION 161
Related products and manuals for Garden shredders Carlton 1712
Garden shredders Carlton 1790 Operator's Manual
(164 pages)
(164 pages)
Garden shredders Carlton 2518 Operator's Manual
(199 pages)
(199 pages)
© 2020, manymanuals.com. All rights reserved. | 1.289 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals