Carlton SP7015 TRX Specifications Page 1

Model SP7015 TRX Machine Serial # _____________ Engine Model # _____________ Engine Specification # _____________ Engine Serial #

SP7015 TRX SAFETY ALERT

STUMP GRINDER LIMITED WARRANTY J.P. Carlton Co. Inc., hereafter referred to as the “Manufacturer”, warrants each new Carlton Grinder to be fre

STUMP GRINDER LIMITED WARRANTY EXPLANATION OF LIMITED WARRANTY The manufacturer will not reimburse the customer or dealer labor cost incurred

Warranty Validation Form Congratulations on your purchase of a Carlton Stump Grinder. This product has been designed and manufactured to provide yea

SP7015 TRX TABLE OF CONTENTS INTRODUCTION FOREWORD 1 GENERAL INFORMATION 2 MACHINE FEATURES 3 MACHINE SPECIFICATI

SP7015 TRX FOREWORD 1 Congratulations on your purchase of a new Carlton® Professional Stump Grinder! Carlton

SP7015 TRX GENERAL INFORMATION 2 The J. P. Carlton Company constantly strives to create the best equipment available in the stump cutting

SP7015 TRX MACHINE FEATURES 3 • Diesel Power • Direct drive hydraulic pump • Hydraulic motor propulsion • Hydraulic contro

SP7015 TRX MACHINE SPECIFICATIONS 4 Engine... Deutz 60 HP Turbo Diesel Weight ...

SP7015 TRX MACHINE SPECIFICATIONS 5

SP7015 TRX SAFETY PRECAUTIONS 6 Before operating the stump cutter, read this manual, the engine manual, and all the safety decals on

SP7015 TRX SAFETY PRECAUTIONS 7 Be Safe and Practice Safe Operation using the following guidelines.

SP7015 TRX SAFETY PRECAUTIONS 8 • Never allow spectators to stand and watch machine in operation w

SP7015 TRX SAFETY PRECAUTIONS 9ATTENTION: The Carlton® Model SP7015 TRX Stump Grinder CAN be overturned on steep inclines. This can c

DIESEL ENGINE EXHAUST WARNING CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the Sta

SP7015 TRX DAILY CHECKLIST 10 DAILY CHECKS SHOULD BE PERFORMED BEFORE STARTING THE ENGINE FOR THE DAY. DO NOT INSERT KEY INT

SP7015 TRX MACHINE CONTROLS 11 ENGINE CONTROLS – Refer to the engine manufacturers owners’ manual for controls, operation, and ser

SP7015 TRX MACHINE CONTROLS 12 • Use the radio transmitter to operate the machine when positioning the machine at the job site a

SP7015 TRX MACHINE CONTROLS 13 HYDRAULIC CONTROLS • A series of hydraulic controls are located on the machine and radio transmit

SP7015 TRX MACHINE CONTROLS 14The Cutter head may be moved in two directions; either up and down or side to side: CUTTER WHEEL (

SP7015 TRX MACHINE CONTROLS 15 FLOW CONTROL • Flow control affects how fast the machine travels. High flow is for moving the ma

SP7015 TRX MACHINE CONTROLS 16SAFETY • NEVER SERVICE A MACHINE WITH THE ENGINE RUNNING, SEVERE PERSONAL INJURY COULD OCCUR. TURN

SP7015 TRX MACHINE CONTROLS 17 TROUBLESHOOTING SEE THE RADIO CONTROL MANUAL FOR ANY OPERATING PROBLEMS WITH THE RADIO RECEIVER &a

SP7015 TRX TRANSPORTING 18 DO NOT TOW! THE MODEL SP7015 TRX IS DESIGNED TO BE TRANSPORTED TO THE JOB SITE AND WILL MOV

SP7015 TRX TRANSPORTING 19 • THE TRAILER MUST BE SECURELY ATTACHED TO THE TOW VEHICLE BEFORE LOADING OR UNLOADING THE

SP7015 TRX MACHINE OPERATION 20 STARTING - READ THIS MANUAL, ALL MACHINE DECALS, AND THE ENGINE MANUAL BEFORE STARTING. • Check a

SP7015 TRX MACHINE OPERATION 21 • Now start the engine, turn the key switch while pressing the by-pass switch to start the machine.

SP7015 TRX MACHINE OPERATION 22 • Cutter head swing speed should be adjusted to a rate that will allow cutter wheel to pass through

SP7015 TRX MACHINE OPERATION 23 • Raise cutter wheel clear of stump and return to center position. • Reduce engine speed to idle.

SP7015 TRX MACHINE MAINTENANCE 24 SAFETY • NEVER SERVICE A MACHINE WITH THE ENGINE RUNNING, SEVERE PERSONAL INJURY COULD OCCUR. TURN ENG

SP7015 TRX MACHINE MAINTENANCE 25 • Clean Poly Chain® belt guard weekly by removing the bottom guard. Chip build-up will wear the Pol

SP7015 TRX MACHINE MAINTENANCE 26Always clean tip of grease gun fitting and grease fitting on machine before attaching hose to prevent dir

SP7015 TRX MACHINE MAINTENANCE 27 • Grease engine slide and engagement handle weekly. Use Texaco® Starplex II grease. TRACK T

SP7015 TRX MACHINE MAINTENANCE 28 • The washer shown here should have a gap of 1/2” between it and the plate when the track is tensione

SP7015 TRX LUBRICATION CHART 29 • The model SP7015 TRX, as well as all of our machines, is built to be a rugged performer. Your n

SP7015 TRX SAFETY ALERT

SP7015 TRX TROUBLESHOOTING GUIDE 30 COMPLAINT CAUSE CORRECTION Engine will not start. (See Engine Manufacturer Manual for further informat

SP7015 TRX TROUBLESHOOTING GUIDE 31 COMPLAINT CAUSE CORRECTION Roar in machine when cutter wheel is engaged. • Belt guards rubbing on jacks

SP7015 TRX SERVICING BELTS 32 Replacing Engine Belt SAFETY • NEVER SERVICE A MACHINE WITH THE ENGINE RUNNING, SEVERE PERSO

SP7015 TRX SERVICING BELTS 33 Replacing Engine Belt • Slide the engine back toward the cutter wheel with the engagement ha

SP7015 TRX SERVICING BELTS 34 Replacing Engine Belt • Replace and tighten the belt keepers. • Replace the

SP7015 TRX SERVICING BELTS 35Replacing Poly Chain® Belt SAFETY • NEVER SERVICE A MACHINE WITH THE ENGINE RUNNING, SEVERE P

SP7015 TRX SERVICING BELTS 36 Replacing Poly Chain® Belt • Loosen the front jam bolts on the underside of the boom box and

SP7015 TRX SERVICING BELTS 37 Replacing Poly Chain® Belt

SP7015 TRX SERVICING BEARINGS 38 SAFETY • NEVER SERVICE A MACHINE WITH THE ENGINE RUNNING, SEVERE PERSONAL INJURY COULD OCCUR. TUR

SP7015 TRX SERVICING BEARINGS 39 SERVICING PIVOT TABLE BEARING While turntable bearings require almost no attention, what little

SP7015 TRX SERVICING CUTTER WHEEL 40 SAFETY • NEVER SERVICE A MACHINE WITH THE ENGINE RUNNING, SEVERE PERSONAL INJURY COULD OCCUR. TURN ENGIN

SP7015 TRX SERVICING CUTTER WHEEL 41TOOTH ARRANGEMENT • Inspect pockets, teeth, and bolts for damage and replace as required. • When replaci

SP7015 TRX SERVICING CUTTER WHEEL 42 OPTIONAL: Sandvik® Dura Disk II Cutter Wheel • If the machine is supplied with the optional Dura Disk II

SP7015 TRX SERVICING CUTTER WHEEL 43 TOOTH ARRANGEMENT • Inspect pockets, teeth and bolts for damage and replace as required. • When replaci

SP7015 TRX SERVICING CUTTER WHEEL 44 TOOTH SHARPENING Begin by chamfering shank back past edge of carbide. You do this because if it is n

SP7015 TRX SERVICING HYDRAULICS 45 SAFETY • NEVER SERVICE A MACHINE WITH THE ENGINE RUNNING, SEVERE PERSONAL INJURY COULD OCCUR. TURN EN

SP7015 TRX SERVICING HYDRAULICS 46 • Replace hydraulic filter every three to four months of normal use. More often if used under severe

SP7015 TRX SERVICING HYDRAULICS 47 REPLACING HYDRAULIC PUMP • Engine must be shut off. • Remove key & disconnect battery cable. •

SP7015 TRX SERVICING STUB SHAFT 48 SAFETY • NEVER SERVICE A MACHINE WITH THE ENGINE RUNNING, SEVERE PERSONAL INJURY COULD OCCUR. TURN

SP7015 TRX SERVICING STUB SHAFT 49 • Next you will need to remove the jackshaft sheave. Remove the bolts in the jackshaft sheave and

SP7015 TRX SAFETY ALERT

SP7015 TRX SERVICING STUB SHAFT 50 • You can now remove the bearing supported stub shaft plate. Remove the bolts holding the shaft

SP7015 TRX SERVICING STUB SHAFT 51 • Replace any parts found defective or worn. Put stub shaft coupling plate onto the flywheel. The

SP7015 TRX SERVICING STUB SHAFT 52 • Bolt grease fitting to the air filter bracket. • Before starting the engine, apply grease to

SP7015 TRX MACHINE WIRING 53 RADIO CONTROL MACHINE DIAGRAM CURRENT7015TRX-1CHECKED BY:J.P. CARLTON CO. DIVISION DAF INCEC #

SP7015 TRX TURNTABLE ASSEMBLY 54 ITEM NO PART NO DESCRIPTION QTY 1 0500125 Turntable Bearing 1 2 5/8”-18 x 2 1/2” SHC

SP7015 TRX ENGINE SLIDE ASSEMBLY 55 ITEM NO PART NO DESCRIPTION QTY 1 02001051 Engine - 60 HP Deutz Turbo Diesel 1 2 5/8

SP7015 TRX ENGINE SLIDE ASSEMBLY 56

SP7015 TRX ENGINE BELT ASSEMBLY 57 ITEM NO PART NO DESCRIPTION QTY 1 0400131 Engine Belt - 4B105 1 2 0250105 Sheave - 4B5

SP7015 TRX ENGINE BELT ASSEMBLY 58 NOTE: Make sure the grease fitting is on top of the stub shaft assembly before bolting the st

SP7015 TRX JACKSHAFT ASSEMBLY 59 ITEM NO PART NO DESCRIPTION QTY 1 4404185A Jackshaft – 1 11/16” 1 2 0500144 Outer B

SP7015 TRX POLY CHAIN® ASSEMBLY 60 ITEM NO PART NO DESCRIPTION QTY 1 3504196 Poly Chain® Guard 1 2 3/8”-16 X 1 1/2"

SP7015 TRX CUTTER WHEEL ASSEMBLY 61 ITEM NO PART NO DESCRIPTION QTY 1 0450101 Tooth - Straight 2 2 0450102 Tooth - Right 45° 15

SP7015 TRX CUTTER WHEEL ASSEMBLY 62

SP7015 TRX CHIP GUARD ASSEMBLY 63 ITEM NO PART NO DESCRIPTION QTY 1 44TR151 Chip Deck – Right Hand 1 2 44TR152 Chip De

SP7015 TRX TRACK ASSEMBLY

SP7015 TRX TRACK ASSEMBLY

SP7015 TRX TRACK ASSEMBLY

SP7015 TRX TRACK ASSEMBLY

STUMP CUTTERS MODEL TYPE ENGINE HP FUEL CUTTINGDEPTH CUTTINGHEIGHT CUT SWING NO. TEETH WHEELDI

SP7015 TRX SAFETY ALERT